[Shrother179]

FIBERGLASS RESIN: WARNING. FLAMMABLE LIQUID AND VAPOR. Vapor harmful. May irritate eyes, nose and throat and cause dizziness, headache or nausea. Contains a chemical which can cause cancer. HARDENER: DANGER. OXIDIZER. CONTACT WITH OTHER MATERIAL MAY CAUSE FIRE. CAUSES EYE, SKIN, AND DIGESTIVE TRACT BURNS. MAY BE HARMFUL IF SWALLOWED OR INHALED. May irritate nose and throat. . PRECAUTIONS: Keep from contact with clothing and other combustible materials. Store in tightly closed container. Vapor may cause flash fire. Keep away from heat, sparks, flame and sources of static discharge. Do not get in eyes, on skin or clothing. Avoid breathing dust or vapor. Use only with adequate ventilation. Do not swallow. Wear eye and face protection. Goggles are recommended for eye protection. Wear suitable gloves and protective clothing. Wash thoroughly after handling. Close container after each use. FIRST AID INFORMATION: INHALATION: Remove person to fresh air. If you feel unwell, get medical attention. SKIN CONTACT: Immediately flush with large amounts of water for at least 15 minutes. Remove contaminated clothing. Get immediate medical attention. Wash clothing before reuse. EYE CONTACT: Immediately flush with large amounts of water for at least 15 minutes. Remove contact lenses if easy to do. Continue rinsing. Immediately get medical attention. IF SWALLOWED: Do not induce vomiting. Call physician immediately. KEEP OUT OF REACH OF CHILDREN. CONTAINS: FIBERGLASS RESIN: Polyester Polymer; Styrene Monomer (100-42-5); Silica (7631-86-9). LIQUID HARDENER: Dimethyl Phthalate (131-11-3); Methyl Ethyl Ketone Peroxide (1338-23-4); . 2,2,4-Trimethyl-1,3-Pentanediol Diisobutyrate (6846-50-0); Methyl Ethyl Ketone (78-93-3); Hydrogen Peroxide (7722-84-1); Water (7732-18-5)

[babisuu]

Ingredients: Contains: Fiberglass Resin: Polyester Polymer; Styrene Monomer (100-42-5); Silica (7631-86-9). Liquid Hardener: Dimethyl Phthalate (131-11-3); Methyl Ethyl Ketone Peroxide (1338-23-4); 2,2,4-Trimethyl-1,3-Pentanediol Diisobutyrate (6846-50-0); Methyl Ethyl Ketone (78-93-3); Hydrogen Peroxide (7722-84-1); Water (7732-18-5).

[thufir]

Instructions: . Directions for Use (Read all directions and warning for proper application):. 1. Clean repair area with acetone or warm, soapy water to remove all dirt, grease, oil and contaminants. Let dry completely. 2. Cut away damaged area and loose pieces. Sand the surface with 3M? Sandpaper 80 grit to remove all primer, paint, rust, or gel-coat. Sand 1-2 inches beyond damaged area should be repaired for added strength. Depress or slightly bend the edges of solid metal inward. Remove all dust created from sanding with a dry cloth or compressed air. Re-clean the surface as in Step 1. 3. Pre-cut several pieces of Fiberglass Cloth to 1 inch larger than hole. Wearing gloves is recommended for the next steps. 4. Mixing tips: Working life of mixed resin is approximately 8-12 minutes at 75°F. Mix in small amounts. Mixing large amounts at one time will reduce the working time of the mixed resin. Never mix hardener in the resin bottle. Do not mix the entire container with liquid hardener. Mixed Bondo® Fiberglass Resin with Bondo® Fiberglass Resin Liquid Hardener in the mixing tray supplied. Do not use waxed cup. Use a push pin or thumbtack to open the hardener tube. Scrape sides and bottom of tray to ensure thorough mixing. Mix as follows: Mix resin and hardener in mixing tray supplied. Estimate amount of resin needed to saturate Fiberglass Cloth. Ratio of resin to hardener is as follows: For 1 ounce of resin, add 10 drops of hardener or 6 tablespoons of resin with ¼ teaspoon of hardener. Make small batches at a time and mix more as needed. 5. Brush a coat of mixed resin on the damaged area extending 2-3 inches beyond repair. Place the first layer of Fiberglass Cloth onto mixed resin. Use paint brush to saturate the cloth with mixed resin. A dabbing motion will help saturate the cloth and remove any air pockets. Continue applying additional layers of cloth and mixed resin as needed while the first application is still sticky or wet. If the surface dries hard and is no longer sticky, sand with 3M? Sandpaper 80 grit before applying additional layers of mixed resin and cloth. Follow the same procedure if both sides are being repaired. 6. Allow material to cure, approximately 2 hours at 75°F. Curing will take longer at cold temperatures. Once cured, sand repaired area with 3M? Sandpaper 80 grit. Option: To return the contour or to smooth out low areas in the surface, use a layer of Bondo® Body Filler. 7. Feather the edge of the repaired area with 3M? Sandpaper 180 grit to blend the repair into the undamaged surface. 8. The surface is now ready for paint, primer or gel coat, per the manufacturers' recommendation. . 9. While resin is still wet, clean paint brush or tools with acetone or lacquer thinner. . 10. Do not put mixed, unused resin back into the container. It will harden the rest of the contents.

[s20-10s]

Overall, I was pleasantly surprised with the Devcon Epoxy Bathtub Repair Kit. The almond finish matched surprisingly well and I was happy with the flush finish. I also ended up putting a curtain rod up, which made the patched-up holes barely noticeable. But let me know what you think. If you’ve tried this project, feel free to share what worked for you in the comments below… or let me know what you’d do differently. [links]

[acrylicist]

Using the toothpick, place the epoxy directly in the screw holes. It’s ok if it drips out a little. You’ll be adding more epoxy in the next step. Since my holes were small I only used epoxy if you have a larger hole and need additional strength the kit will come with some fiber mesh to cover the larger hole and provide the additional strength once dry. here

[Arcturus]

Remove the plastic sheet and sand over the epoxy with 60 grit sandpaper. This is the roughest sandpaper I used and is meant to quickly remove the excess epoxy. Do not sand the surface of your tub surround with this sandpaper or it will remove the finish. here

[Timothy]

For this example, I was patching screw holes left behind after I removed a glass shower door from my tub/shower surround. Overall I had a total of 6 holes to fill and I ordered 2 kits and did 1 side (3 holes) at a time. This Playlist shows the whole project on our YouTube Channel.

[destinbrides]

I will admit in the past I have paid over $1,500 to get a tub surround replaced which could have been fixed with this solution. Since then I have learned a few things and one of those things is how to repair holes in a fiberglass surround ensuring a watertight surface and something that isn’t an eyesore.

[Guybrush01]

Warning: You only have about 5 minutes of working time before the epoxy starts to firm up so make sure you have everything ready once you get to this step. more

[Zerbie]

marine tex mixed with pigment for matching color here

[aidos]

will this work, or should i use white all over, and tint the gray with a gray pigment? Does that make any sense? I guess what I'm asking, is there any chemical difference between the gray and white marine-tex. thanks for the help. ac.

[MrMagic]

Re: Filling old screw holes in a fiberglass boat.

[corwin78]

sounds to me like a job for marine-tex here

[dporter05]

Re: Filling old screw holes in a fiberglass boat.

[DjeZAeL]

If you are at an office or shared network, you can ask the network administrator to run a scan across the network looking for misconfigured or infected devices. here

[sunny256]

Another way to prevent getting this page in the future is to use Privacy Pass. You may need to download version 2.0 now from the Chrome Web Store.

[r1chb]

Completing the CAPTCHA proves you are a human and gives you temporary access to the web property.

[fabianhjr]

If you are on a personal connection, like at home, you can run an anti-virus scan on your device to make sure it is not infected with malware. here

[KInkade341]

Cloudflare Ray ID: 687c1ab68bdb2de4 • Your IP : 46.32.66.208 • Performance & security by Cloudflare