[lakshmi]

The best course of action for a tree that is being strangled is to remove the strangling material, such as rope, immediately. Using sharp clippers or shears, remove as much of the strangling material as you can. Don’t worry too much about getting every bit of the material; in some parts of the tree, such as branch forks, the rope may be embedded permanently. Counter the strangulation effect by ensuring the tree is no longer encircled by the strangling material so the tree can grow outward without encountering resistance. more

[rainchains]

Trees grow outward as well as upward. Their outermost layers, right beneath the bark, are their newest portions while old wood, heartwood, at their center eventually turns brown and dies. A tree’s important activities, including getting nutrients and moisture from its roots to its leaves, take place in the outer layers. If those processes are interrupted, the tree will become sick and eventually die. here

[michaelboyd85]

If you have a tree that someone bound with rope, you may notice that the tree is ailing. The problem probably was caused by strangulation. Although plant strangulation is a slow process, it is a very real danger, eventually killing the plant. Luckily, you may be able to save the rope-bound tree if you act quickly.

[uncaer9]

Strangulation occurs when a tree can no longer function properly because its vital processes are cut off. When surrounded by rope, wire or another thin, binding material, a tree continues to grow outward around the obstruction. Eventually, the material can become embedded in all or part of the tree, cutting off the tree's circulation of nutrients and water. If the situation is not remedied in time, the situation will kill the tree.

[Artefact2]

This should help loosen the magnet.

[gohan]

Finish up the process by applying wax and buffing to a shine.

[johnriderjr0]

If you don't have an outlet nearby, use a battery operated hair dryer. here

[randomguy7]

1. Test the car trunk latch. If you have a remote control for the trunk but pressing the release button doesn’t work, use your trunk key to open the trunk manually. here

[bradford1Merrill]

4. Remove dirt and debris from the mechanism by spraying compressed air into it. [links]

[andy]

3. Inspect the mechanism of the latch to check whether there is a broken plastic component. Any broken parts will need to be fixed by a qualified mechanic. [links]

[Frost987]

Need Help Opening a Locked Car Trunk? [links]

[bittard]

2. If your car is equipped with a manual car trunk latch release, locate this inside your vehicle. In a minivan, this feature may be found on the inside of the vehicle’s luggage area underneath a trim panel. In other cars, generally, it can be found either at the back of the car trunk or by the wheel well on the trunk’s sides. This mechanism can be an actual lever like a ripcord or a button. [links]

[michaelboyd85]

Now that the driveshaft is free from the outside axle, it's time to pull the shaft from the car. The port (left) side shaft attaches directly at the differential. The starboard side driveshaft passes through an intermediate bearing in a race attached to the engine crankcase. This bearing is held in place with two long screws with a head that has an 'ear' on one side (8 on the photo below). The 'ears' hold the bearing in place. The long screws are anchored with locknuts (7 in the photo) that are on the differential side of the bearing race. The easiest way to reach these two nuts is from underneath. A stubby ratchet wrench is indispensable!! Get the socket set in place and work it until it feels really loose. This means the long bolts are loose. Feel around on the other side of the race and you will find them. here

[JoesphCros]

The triax case is larger than the indented portion on the hook; use the flat side against the back of the case. Make sure the flat side is towards you. [links]

[Barnabe]

First, separate the hook from the shaft. [links]

[Osndok]

You will need to reach up through the opening under the car, in the crossmember just aft of the motor, and position the hook next to the inboard side of the triax case. Sorry, no photos from under the car. In this photo the threaded hole in the hook is visible just past the triax case. That's the rubber boot of the triax visible in the front. [links]

[Matthias Vance]

I have yet to see a car where these wires have not been cut. They are cut because Citroen routed the wires along the lower arm to the caliper. To disconnect the lower arm, the wires must be disconnected and unraveled from the caliper, something that requires loosening several more screws. Or you can cut the wire. Guess what most shops do? This is a prime example of one engineer not talking to another, or the design team not looking at what happens to their work out in the real world. I'm sure there is a reason for routing the wires along the lower arm that is compl�tement logique, probably relating to less wear or stress on the wire. But in practice, this design forces additional work to separate the lower arm from the pivot. If the wiring were routed along the upper arm, a balljoint or driveshaft job could be done without removing the wires. The guy who designed the wiring never looked at the tasks involved in a balljoint job or a driveshaft job. I see examples of this type of bullshit engineering time and again on these cars. [links]

[e_cockroach]

Are you having issues with your headphones not connecting to bluetooth? Here is a step-by-step page to help you to Reset Bluetooth Headphones. This step by step will help with all brands of headphones including, Apple Headphones, Beats Headphones, Blackweb Headphones, Bose Headphones, Jabra Headphones, JBL Headphones, JVC Headphones, LG Headphones, MPOW Headphones, ONN Headphones, Skullcandy Headphones, Sony Headphones, and TaoTronics Headphones.

[cookie]

Method #1
1 – Try using a Paper-mate or BIC pen.
2 – Remove the inner piece with the ink in it (ink cartridge).
3 – Slide the END of the ink cartridge down onto the metal jack.
4 – Push it down as far as it will go to try and get the ink cartridge plastic around the broken jack.
5 – Once you have it all the way down, pull up slowly and the broken jack should slide out. more

[j16sdiz]

How to remove a broken headphone plug from audio jack, Easy, Subtitle Instructions
Ear bud plug break inside computer audio jack – Pause the video to read if it goes to fast for you

[chrisdbc]

Headphone has broken in phone audio jack – Headphone Jack Broke Off In Phone

[george14]

Tool kits for phones

[paulhickey103]

Method #4
1 – Use a coffee stir straw or something similar.
2 – Use a hot glue gun and add a small amount of hot glue to the end.
3 – Slide the straw with the hot glue onto the broken piece in the jack and let sit for 30 seconds.
4 – After 30 seconds slowly and carefully pull the straw out and the broken head jack should be removed. [links]