[LuciferUA]

I recently had to remove the belt on my 2001 volvo penta 3.0GSP-A so I could remove some remaining pieces of impeller that were wedged in my circulating pump housing, in doing so I discovered that the 1/2" drive slot was broken (port-side facing). when I read the steps in the SELOC manual on releaving the tension, it makes it sound so simple "loosen the tensioner pulley bolt, then insert a 1/2" drive breaker bar and "swing" the pulley up to loosen the tension" wasn't so easy, and nothing seemed to "swing" as much as I would have hoped, and the broken square hole made it much more difficult and I basically had to relieve the tension by pulling the alternator.

[carol88miller]

Have a new tensioner getting shipped today, but was thinking maybe a ratchet strap around something outside of the boat and a few clicks at a time would pull that tensioner back far enough to hopefully "reset" itself so I can get on the water this weekend but don't want to waste my time if the consensus is that the tensioner is just junk and a new tensioner is the only thing that is going to fix it. just seems like there should be a way to "unlock" these auto-tensioners, and then "lock" them to supply adequate tension after you have done what you need to do and have the belt back in position.

[dhaniellemar63]

once everything was complete and put back together, i managed to man-handle the belt tensioner enough to slip the belt back on, but now there is about an inch and a half of play, and if I push down on the belt with moderate force, the tensioner pulley swings up the whole way. not good because now obviously I have a lot of belt slips and squeals, and a new symptom of pretty rough idleing (once up on plane squeals pretty much stop and engine sounds great) but not putting the boat back in the water til I have sufficient tension.

[hugolp]

OEM No/Model: 3582324
Genuine OEM Volvo Penta Engine Serpentine Belt Tensioner - 3860079

[SEN-5241]

Tensioner functions:
In the process of installation,need assure to tensioning the toothed belt ,so that can compensate the cumulative error of each part in the system(diameter,location,the belt length ext.
to provide a constant tension of the belt within the operating temperature and the load ,and the life of the time(diameter location ,the belt length ect)
to provide a constant tension of the belt within the operating temperature and the load ,and the life of the time
no matter what the operation conditions,both for belt drive system provides effective damping to prevent the belt jumping put from range
in order to reduce the noise ,the belt tensioning fore can be settled as small as possible
Tensioner advantages:
In its operation life,it can maintain high precision timing
Longer life
Lower noise
Simple maintenance and installation
No need of lubrication in its operationing
Compact structure
Low friction
High efficiency
AINATE company was founds in 1989,is located in ruian city Zhejiang province. as the OEM standards as our rules into production,is specialized in manufacturing tensioner pulley,belt tensioner,and timing tesionerser series,is now producing more than 200 items,are suitable for Volkswagen, Audi, General Motors, Peugeot ,Opel, Daewoo and so on .And export in North America,South America,Western Europe,Eastern Asia,Southeast Asia,Africa,Oceania,and Other countries and regions.

AINATE is mainly engaged in automobile faensioner pulley ,belt tensioner,and timingtesionerser desining, development and production.

AINATE is well-equipped ,strong enterprise . It has tons of high-injection die-casting machines, automatic injection molding machine,CNC machine and various models of punch,hydraulic machine,milling machines and other machines and test equipments .

We keep good cooperation with domestic professional brand companies
We will be meet and surpass our clients demands with good quality ,professional service .
Trust us ,we will give you surprise . AINATE tensioner welcome to you.

[BitcoinCyberStore.com]

Ruian AiNaTe Auto Parts Co., Ltd is a specialized auto tensioner manufacturer. Since the inception, Our company has been manufacturing products strictly according to OEM standard. Our product covers most of cars in the world like Japanese cars Korean cars, European cars, and American cars, etc. We . [Read More]

[loadingpicker87]

As you might expect, the Sterndrive system of the Volvo Penta is largely comprised of pulleys that relay power throughout the engine. One of the main components of this Volvo engine is the idler pulley that makes sure that the right amount of tension is held on the internal engine drive belt of the Volvo Penta. Additionally, there is also a tensioner pulley that does a similar job but is mounted on an adjustable bolt. here

[DayLightStranger]

What parts make up the Sterndrive system of Volvo Pentas? here

[riggasconi]

How do these parts affect the performance of Volvo Pentas? more

[Naniscegine]

Volvo Penta engines using the Sterndrive package are considered some of the more high-performing, efficient boat motors available on the marine market today. It is a complete system with components for trim and tilt and a low fuel consumption design that will extend your boating trip. Still, over the years, you may need to replace some of the engine components like the belts and pulleys of the Sterndrive system.

[helg]

How do you replace serpentine belts in a Volvo Penta?

[ralphmcclure]

The only place I noticed it lower was ebay for 105.04. But in all honesty what normal business can compete with ebay.
New Volvo Penta Engine Serpentine Belt Tensioner 3860079 | eBay

[fergalish]

Hi, I don't know of anyone here who would read your question and choose not to reply because it is a stupid question. I for one checked the thread because belt problems on these engines are fairly common but they are caused by the power steering pulley not the tensioner. Therefore, I cannot for sure help.

[Count042]

Re: 5.7gi-ef serpentine belt issue and tensioner here

[Klintel]

Re: 5.7gi-ef serpentine belt issue and tensioner here

[songcopy65]

Re: 5.7gi-ef serpentine belt issue and tensioner

[The Madhatter]

Re: 5.7gi-ef serpentine belt issue and tensioner

[td]

If parts arrive damaged in shipment, it is the customer's responsibility to notify the carrier immediately and reject the damaged package. Contact Michigan Motorz of the potential damage. A claim will be filed and we will send out the identical part. If parts are damaged in shipment and the customer does not notice damage, please call Michigan Motorz, LLC. [links]

[joey]

All oil & lubricating fluids are drained before they are sent out (this is required by our freight carriers). All engines & parts are packed by our shipping department. Engines are then inspected by our shipping manager before they are loaded onto a freight carrier. here

[shiraroberts112]

In Stock - Ships today if ordered ONLINE before 2 PM EST!

[zmauricepittmanj]

For items received as described, a refund of the final invoice price (minus shipping and handling charges and a 15% restocking fee) will be issued. Buyer is responsible for return shipping costs and for sufficiently packing and insuring returned items unless otherwise agreed upon. Refunds will not be issued for damaged merchandise. All returns must be made within 15 days of delivery to you. No refunds for electronic parts if the box is opened. All returns must have an RMA # and invoice #. 15% restocking fee on the return of any complete engine. Please call or email for an RMA #. [links]

[endian7000]

*= No Sales Tax OUTSIDE the state of Michigan. Orders placed over the phone or through our website will be charged 6% for sales tax within the state of Michigan.

[xterm11]

Canadian Shipments more