See full version: NOCO GENPRO10X1 1-Bank, 10-Amp On-Board Battery Charger & Maintainer
Protection
IP Rating: IP68 Safety Short-Circuit: Yes Open-Circuit: Yes Overheating: Yes Overcharge: Yes Spark-Proof: Yes Reverse Polarity: Yes Size Height: 5.6 Inches (141mm) Width: 5.8 Inches (147mm) Depth: 2.8 Inches (72mm) Weight: 5.33 Pounds (2.42kg) here
Operating Requirements
Line Voltage: 120V to 240V
AC Frequency: 50Hz to 60Hz
Operating Temperature: -4° to 104° F (-20° to 50° C)
Storage Temperature: -22° to 140° F (-30° to 60° C)
Relative Humidity: 0 to 95% Non-Condensing
Charging Current: 10 Amps DC x 1 Bank
Voltages: 12V
Chemistry: Lead-Acid and Lithium
Types: Wet, Gel, MF, CA, EFB, AGM, Lithium
Battery Capacity Range: Up to 230 Amp-Hours
Maintenance: All Battery Sizes
Power Consumption: 150 Watts (Max) X 1 Bank
Cord Management
DC Cable + Eyelet Length: 72 Inches (182cm)
DC Cable Size: 14 AWG
DC Fuse Size: 15 AMP MINI ® Blade Fuse
AC Cable Length: 72 Inches (182cm)
AC Cable Size: 18 AWG Oil, gas, grease, water, chemical, UV, abrasion resistant more
Protects against adverse and abnormal conditions, like reverse polarity, sparks, overcharging, over-current, open circuits, short circuits and overheating. more
We don't design something that merely works, but remains safe after a major failure. So we built-in redundant levels of safety protection. more
A mix of electrical engineering and industrial design create a powerful, yet space-efficient charger that can easy to mount anywhere in your boat or equipment. It uses high-frequency switch-mode technology to efficiency convert A/C power into safe D/C power for battery charging. And its onboard microcomputer precisely controls the charging to minimize power loss to create an incredibly compact form factor.
Recharging your battery fast and efficient is essential. But selecting the proper onboard battery charger for your application is equally important. Our On-Board Battery Chargers charge at either 4-amps per bank (GEN Mini-Series) or 10-amps per bank (GEN Series). Whether you have a boat, trolling motor, or trailer, the GEN Series charges a standard deep-cycle marine battery in less than half the time of the GEN Mini Series.
Dynamically alters the charging process based on organic battery feedback allowing for precision battery charging.
A mix of electrical engineering and industrial design create a powerful, yet space-efficient charger that can easy to mount anywhere in your boat or equipment. It uses high-frequency switch-mode technology to efficiency convert A/C power into safe D/C power for battery charging. And its onboard microcomputer precisely controls the charging to minimize power loss to create an incredibly compact form factor.
Protects against adverse and abnormal conditions, like reverse polarity, sparks, overcharging, over-current, open circuits, short circuits and overheating. more
Dynamically alters the charging process based on organic battery feedback allowing for precision battery charging. here
A mix of electrical engineering and industrial design create a powerful, yet space-efficient charger that can easy to mount anywhere in your boat or equipment. It uses high-frequency switch-mode technology to efficiency convert A/C power into safe D/C power for battery charging. And its onboard microcomputer precisely controls the charging to minimize power loss to create an incredibly compact form factor. here
Protects against adverse and abnormal conditions, like reverse polarity, sparks, overcharging, over-current, open circuits, short circuits and overheating. here
Q. Can I connect the charger to only one battery? What do I do with the unused leads or terminals? here
this is what it says on website. here
A. If you are using a waterproof charger and want to charge 1 battery on a 2 bank charger, you will need to connect both leads on that one battery. If you are charging 1 or 2 batteries with a 3 bank charger, you will need to connect all the leads on the 1 or 2 batteries. At no time should the charger be run without all the leads being connected to a battery(s). here
ok guys and gals. i got a 2 bank 4amp/4amp onboard battery charger. it is sealed and waterproof. i read from the website that i can hook both leads to 1 battery for charging 1 at a time? is this ok to do? first time i used it it got really hot but charged the battery. just dont want to screw nothing up. more
just want to make sure it will work out ok with no harm since it got very hot. i havent tried it with 2 batteries yet.