See full version: Installing a Boat Ignition Switch
Using the same procedure as connecting the battery cable to the boat ignition switch, you should now connect the positive wires from the accessories. Connect the ring terminal on the appropriate post for accessories and tighten with a nutdriver or small socket wrench.
Your boat ignition switch is an important part of the starting process. It is connected to the starter through the boat's 12V system. When it is turned on the switch completes the circuit connecting the solenoid to the battery. This then enables the starter to turn over the engine so that it will run. Installing a boat ignition switch is an easy process that requires a few simple hand tools and a few hours of your time. Here are the steps to install a new ignition switch on your boat.
Determine the best location for it on your control panel. Find a place where there are not steering components or other wires that you will be drilling in to.
Take the positive battery wire and connect it to the positive terminal on the ignition switch. Use a nutdriver, or a small socket wrench to tighten the set screws to hold the cable in place. [links]
Lay the ignition switch cylinder onto the surface where you are going to position it. Mark the console and then drill out the hole that will accept the ignition switch. Do not make the hole too big of the retaining clamp will slide through the hole.
For this step you will need to have a little pre-planning. You will need to take several wires and crimp them onto a ring terminal. These wires should include the hot wire from the battery, the wire to the solenoid, and any other accessories that you want to run when the ignition is set to on. Think about which different accessories you want powered by the ignition and make sure the appropriate wires are there. If not, then you will need to run some wires from the particular accessory to the ignition switch. Set these wires aside and crimp separate ring terminals on all the positive wires. One for the battery, one for the solenoid, and one for the accessories. more
Rinker boats are built in Syracuse, Indiana with that Midwestern reputation of hard work, attention to detail and a dedication to craftsmanship. [links]
The employees at The Rinker Boat Company share their boating passion with a drive and desire to build something better. This passion is bestowed upon every boat that bears the Rinker name. here
Whether you have a Rinker Captiva sport boat or Express Cruiser, you’ll find OEM discount parts for your Rinker boat here at Great Lakes Skipper. Our huge inventory of Rinker boat parts and accessories includes Rinker boat seats for sale, replacement boat graphics, doors, boat hatches, boat windows, boat cabin hardware, boat steering wheels, switch panels, boat consoles, and many more. Enjoy browsing our online catalog of genuine OEM Rinker boat parts! here
wikiHow marks an article as reader-approved once it receives enough positive feedback. In this case, 80% of readers who voted found the article helpful, earning it our reader-approved status. [links]
There are 14 references cited in this article, which can be found at the bottom of the page. here
This article has been viewed 487,859 times. here
This article was co-authored by Jason Shackelford. Jason Shackelford is the Owner of Stingray Auto Repair, a family owned and operated auto repair shop with locations in Seattle and Redmond, Washington. He has over 24 years of experience in auto repair and services, and every single technician on Jason’s team has more than 10 years of experience.
A faulty ignition switch in your vehicle can cause several problems ranging from your car stalling and all lights going dark to the radio not working unless the key is wiggled from side to side. Once you’ve been able to identify the ignition switch as the source of your trouble, replacing it is often a fairly straightforward process that requires only common hand tools. You should consult an application specific repair manual before starting this project on your own.
Rinker Boat Company is a manufacturer of cruise and pleasure fiberglass boats from 18 to 41 feet long. The oldest American brand for the production of boats of the Rinker Boat Company dates back to the 30s of the 20th century. From modest fishing boats at the White River in Indiana to the recognized world leader in small craft manufacturing, exporting boats to more than 40 countries.
The family business of the former dairy farmer Lossi Rinker and his 2 sons became known as Rinkerbuilt in 1945. Thanks to many of the company's innovations (fiberglass hull production, stationary engines, trimaran contours, etc.) and interesting marketing moves (colored paintwork on the sides, etc.), combined with high quality and careful attention to detail, Rinker boats get a significant advantage over their competitors both in the USA and in other countries.
Rinker is fully responsible for the quality of its boats, as it produces everything, including interior trim elements. The usual problems and problems for owners of other vessels are unfamiliar to the happy owners of Rinker. [links]