costner1367
27.04.2021 10:25:00
Do any of these holes need plugs? i put water in both live wells and no water came out of any hole beside the actual drain hole.
See full version: Drain holes
Do any of these holes need plugs? i put water in both live wells and no water came out of any hole beside the actual drain hole.
Derek,
Defender Marine will have all the fittings you need. just click here. And no, the holes don't need to be plugged.
First off, I am not arguing the point with you. Actually your comments have peaked my interest. It sounds like you knowledge of boat construction far outweighs my own. I was under the impression that Cobalts were a superior built boat and if this is a safety issue, I am very disappointed. [links]
Capstan [Capstern]. A spool-shaped vertical cylinder, mounted on a spindle and bearing, turned by means of levers or bars; used for moving heavy loads, such as hoisting anchors, lifting yards, or careening vessels.
Rib. A small transverse member, often flexible and composed of one or several pieces, that stiffened the outer skin of a hull. Although often a layman’s term for frame, rib is more properly applied to small craft, such as canoes, small boats, certain heavy frames that run from gunwale to gunwale in clinker-built vessels, or vessels whose skin is made of material other than wood. [links]
Quarter timber. A frame in a vessel’s quarter. [links]
When installing the screws, DO NOT TIGHTEN ALL THE WAY. You should apply just enough pressure to slightly squeeze the sealant. What this does is lets the sealant form a gasket, which later after curing, you tighten the screws the rest of the way to compress the gasket and make a water tight seal. here
Many people use silicone, but it doesn't have any adhesive properties and tends to stick only to itself, and shrinks a bit. I switched to using DAP Kwik Seal Tub & Tile adhesive caulk. It stays rubbery when cured, and does have some adhesive qualities, but is not a super strong bond so when I want to remove the piece, it will come off with a little effort. more
Here is a more elaborate bailer, it has a drop down cone.
How To Install A Transom Drain Plug
I have installed a number of drain plugs, and in the beginning I was a bit sloppy about it figuring that I could just slap one on with some silicone and go sailing. They leaked, sometimes letting in gallons over the course of a day sailing and I had to pull them off and rebed them, so here is what I do now. more
Instead of the ball, it has a little door that swings open. Like the other, if you leave this one down when you are not moving fast enough, it will let water come back in.
The absolute best way to get a feel for a kayak is to paddle one on the water. Clearly, this is not always possible. Failing an on-the-water demo, try to at least sit in the kayak before making a decision. If you are looking at buying a used boat from someone, but can’t get a chance to sit in the actual boat you might buy, see if any local kayakers or kayak clubs or retailers have the same model and will let you sit in theirs. Make sure the boat is appropriate for your body size. [links]
Thigh-hooks: Thigh hooks allow more lower-body movement to transfer to the boat. With the legs inside the boat, a kayaker moves his or her upper body independent from their lower body. The upper body controls the paddle and the boat’s rotation or spin, while the lower body controls the boat’s tilt. The key to boat control is the ability to lift or dip the boat’s edges using hula-dancer-like movements. The knees and lower thighs transmit their movements to the boat via the thigh hooks; the boat then becomes an extension of the lower body. Aggressive hooks reach further down holding more of the kayaker’s legs, resulting in more control. Less aggressive hooks still hold the legs, but are out of the way when the paddler exits the boat. here
Primary stability is the relative stability of a boat that is sitting flat on the water right-side-up. A wider base gives increased primary stability. Planing hulls tend to be wider at the water line and thus provide more primary stability. In flat, motionless water, a planing-hulled boat is harder to flip over than a displacement hulled boat. here
Rescue Bag: All boaters should carry a rescue bag. They fit in even the smallest rodeo boat and can save a life. For a swimmer rescue, 1/4 inch rope is adequate, but can be difficult to hold on to. 3/8 inch rope is easier to hold, and much stronger.
Outfitting and Glue: Stock boats rarely fit the paddler very well. In order to be in total control of a boat, a tight fit must be achieved. Contoured padding is a must for folks who want optimum performance from their craft. At the very least, hip pads should be added to the sides of the saddle. These transfer power from the body to the boat. A more aggressive play-boater will want to customize his or her entire boat to get a glove-like fit. Most individual Padz are self-adhering. The more comprehensive outfit kits require separate glue. H2Glue works great.