See full version: Yamaha t8 tilt motor working wont raise
I don't have the special wrench for removing the pistons but is that what I need to do? I've tried several different methods for filling it and nothing has helped besides make a HUGE mess of fluid everywhere from opening the apparently pressured fill plug. [links]
For instance if I have the motor forced down to within 1/2" of all the way, crack the manual valve/screw on the side, the 2 trim pistons will push the motor up 2-3". I then manually lifted the motor all the way and set it on the service locks. Leave the manual valve open and fill the reservoir. Put the drain back on, then manually lower the motor. Every goes fine until I hit the slow speed 2 trim pistons. It just won't go down. I push it down as far as I can and close the manual trim screw. Then I try to cycle the trim/tilt electrically and it won't up to the high speed ram and won't retract.
2005 90TLRD. The high speed single tilt ram was working ok, but the low speed 2 piston trim system was very slow and wouldn't retract all the way. I tried adding fluid and just began having tons of issues. It seems like there is air under the 2 pistons. here
Update: Currently where I'm at is that I can use the tilt/trim to trim/tilt all the way up. Then I use the manual screw but the motor will only lower to the 2 trim pistons. Once it hits the 2 pistons. it's SOLID. As in I can hang off the motor and it won't budge.
thanks
[links]
An authorized Yamaha mechanic suggested the Relay Assembly (6H1-81950-00-00) might be faulty so I changed it with a new one and no cure. here
My only thought on this is the main wiring harness from the outboard to the control box/key switch is the culprit. I think its unlikely because the contacts appear new on both ends with no damage/pinching on the cable housing. more
I bypassed the kill switch and still no power at the key switch. I checked the control box wiring and no visual signs of damage.
I have a 1992 Pro50 (P50TLRQ) that has electrical issues. more
Other then that, all other electrical components on the boat is working perfectly. The trim and tilt switch on the outboard is working perfectly. I checked every electrical line for damage and or corrosion and there were none. All fuses were in working order. All brushes in the starter are clean. here
Another way to prevent getting this page in the future is to use Privacy Pass. You may need to download version 2.0 now from the Chrome Web Store.
Completing the CAPTCHA proves you are a human and gives you temporary access to the web property.
If you are on a personal connection, like at home, you can run an anti-virus scan on your device to make sure it is not infected with malware.
If you are at an office or shared network, you can ask the network administrator to run a scan across the network looking for misconfigured or infected devices.
Cloudflare Ray ID: 687a2a666d6b3a65 • Your IP : 46.32.66.208 • Performance & security by Cloudflare [links]
[links]
ARCO Marine. 3921 W. Navy Blvd. Pensacola, FL 32507. Toll Free: 1-800-722-2720. arco@arcomarine.com. M - Th | 7:00 a - 5:30 Yamaha Trim/Tilt Motor Kit 115-225HP 1987-1991 With Adaptor Harness 6G5-43880-00: Details. Arco Marine 6240 Tilt/Trim Motor Regular Price: $282.00 Our Price: $211.99 API PT603NM-3 YAMAHA TRIM/TILT MOTOR, 4-WIRE 61A-43880-02-0 Trim/tilt motor för Yamaha typ 6 Modelltyper Yamaha: • 40Y (05-07), 40V (03), C40 (02), F40 (02), F50, FT50 (02-07) Mer information: • 3-bultar • 2 kablar • Flänsens ytterdiameter: Ø 60mm • Axelns längd: 39mm • Total längd: 155mm Observera! För att garantitiden om 2 år ska vara giltig måste trimmotorn målas med grundfärg samt motorfärg
The Tilt Trim Motor are the essential tools to operate your boat more efficiently and safely. Their proper use greatly increases the way the hull is designed to operate in calm water. Whether you are sailing on lakes, rivers, bays or in the open sea, they are absolutely priceless and can help you turn a rough ride into a fun ride Yamaha Outboard Replacement Tilt/Trim Motor, 12v, Reversible 63P-43880-01-00 OBB Starters and Alternator If my 2005 Yamaha F90 sits for a couple of weeks the up tilt and trim won't work unless I start the engine. Then it works fine unless it sits for a while again. The down switch always works. The up switch clicks distinctly but no response from the motor. I looked at the connections and can't find a problem
Page 49: Power Trim And Tilt Switch On Bottom Cowling Components pages 91 and 93. falling overboard and could distract the operator, increasing the risk of collision with another boat or an obstacle. ZMU06234 ZMU05823 EMU42260 Power trim and tilt switches The power trim and tilt system adjusts the outboard motor angle in relation to the tran- som 90 hp Yamaha outboard trim and tilt only works occasionally. Mechanic's Assistant: Sometimes boat issues seem like they'll be really complicated, but end up being easy to fix. The Marine Mechanic I'm going to connect you with knows all the tricks and shortcuts Trim/tilt motor Yamaha type 5 (115-225 hp) Product details. Electric trim/tilt motor for Yamaha type 5 Modeltypes Yamaha: 100A (64W, 1996) 115B (6E5, 1988-1996) For the 2-year warranty-period to be valid you will need to paint the trim-motor using primer-paint and engine-paint. This will extend the lifeline of the trim-motor considerably
Volvo Penta Tilt & Trim Motor. Used on Volvo Penta All models 2001-on SX Lester 10851. £141.20 (£117.67 exc. VAT) View; Buy no Trim Tilt Motor - Yamaha 115-300hp 2-stroke, 115-250hp 4-stroke . $169.95. Add to Cart. Add to Wish List Add to Compare. Trim Tilt Motor - Yamaha 25-40hp 4-stroke . $169.96. Add to Cart. Add to Wish List Add to Compare. View as Grid List. 18 Items . Show. per page. Sort By. Set. more